|
NYLATRON®
Nylatron
is a tradename for a family of high performance nylon products made by
Quadrant Engineering Plastic Products, Inc., including:
- Nylatron
GS Nylon
- Nylatron
GSM Nylon
- Nylatron
GSM Blue Nylon
- Nylatron
NSM Nylon
Quadramt
also produces Nylon 101, MC 901, MC 907 NylasteelTM, and 30% Glass-Filled
Nylon. The following charts define and compare the different grades available:
| |
Small/Screw
Machine Nylon Parts
(Extruded Type 6/6) |
Larger
or Near Net Nylon Shapes
(Cast Type 6 Nylons) |
| For
general purpose wear and structural parts. (FDA grades available)
|
Polypenco®
Nylon 101
Of all the unmodified
nylons, Polypenco® Nylon 101 is the strongest, most rigid and has
one of the highest melting points. It is commonly specified for screw
machined electrical insulators and food contact parts.
It is stocked in both
natural and black. Other colors are available on a custom basis.
Polypenco Nylon 101 natural is FDA, USDA, NSF, and 3A-Dairy compliant.
|
MC®
901 Nylon
Heat stabilized
nylon offering long-term thermal stability to 260ºF. It is blue in
color and used in a variety of bearing and structural applications
such as wheels, gears, and custom parts.
MC®
907 Nylon
Unmodified type 6 nylon offering the highest strength and hardness
of the nylon 6 grades. MC 907 natural is FDA, USDA and 3A-Dairy
compliant. It is off-white and primarily used for food contact parts.
|
| For
improved load bearing capability |
Nylatron®
GS Nylon
Molybdenum disulphide (MoS2) filled nylon offering improved
strength and rigidity. With a lower coefficient of linear thermal
expansion than Nylon 101, Nylatron GS parts maintain better fit and
clearances, and have less tendency to seize as bearings. |
Nylatron®
GSM Nylon
Nylatron GSM contains finely divided particles of molybdenum disulphide
(MoS2) to enhance its load bearing capabilities while maintaining
the impact resistance inherent to nylon. It is the most commonly used
grade for gears, sheaves, sprockets and custom parts. It is grey-black
in color. |
| For
best wear resistance and lowest coefficient of friction |
.
|
Nylatron®
NSM Nylon
Best bearing and wear nylon product available today. Proprietary
type 6 nylon formulation produced using Quadrant's Monocast® process.
Solid lubricant additives impart self-lubricating, high pressure/velocity
and superior wear resistance characteristics. Nylatron NSM was developed
specifically for demanding applications where larger size parts are
required. It is ideal for bearings, gears and wear pads.
In wear applications,
Nylatron NSM lasts up to 10 times longer than standard Type 6 nylon.
|
| For
improved load capacity or For improved frictional characteristics
|
30%
Glass-reinforced Nylon 6/6
For applications requiring higher compressive strength and rigidity,
30% glass reinforced Nylon 6/6 is also available. It is stocked in
diameters ranging from 10mm to 150mm (or .394" to 5.910"
in meter lengths). |
Nylatron®
GSM Blue Nylon
(Oil-filled)
The first cast nylon to combine both molybdenum disulphid (MoS²) and
oil for the load capacity of Nylatron GSM nylon, plus improved frictional
characteristics. It excels in higher pressures, and at low speeds-up
to 40 fpm. It offers 20% lower coefficient of friction, 50% greater
limiting PV, and a lower "k" factor than Nylatron GSM, and
the lowest "slip-stick" of any nylon product making it ideal
for slide pads, thrust washers and trunion bearings. Nylatron GSM
Blue should be considered for any oil-filled nylon application. It
is dark blue in color. |
MC®
901 Blue
| Property |
Method |
Unit |
Value |
| Mechanical |
| Specific
Gravity, 73°F |
D792 |
|
1.15 |
| Tensile
Strength, 73°F |
D638 |
psi |
12,000 |
| Tensile
Modulus of Elasticity, 73°F |
D638 |
psi |
400,000 |
| Elongation,
73°F |
D638 |
% |
20.0 |
| Flexural
Strength, 73°F |
D790 |
psi |
16,000 |
| Flexural
Modulus, 73°F |
D790 |
psi |
500,000 |
| Shear
Strength, 73°F |
D732 |
psi |
11,000 |
| Compressive
Strength, 10% Def., 73°F |
D695 |
psi |
15,000 |
| Compressive
Modulus of Elasticity, 73°F |
D695 |
psi |
400,000 |
| Hardness,
Rockwell, Scale as noted, 73°F |
D785 |
|
M85
(R115) |
| Hardness,
Durometer, Shore D scale, 73°F |
D2240 |
|
D85 |
| Izod
Impact (notched), 73°F |
D256
Type A |
ft-lb/in |
0.4 |
| Coefficient
of Friction (Dry vs Steel) Dynamic |
PTM55007 |
|
0.20 |
| Limiting
PV, 73°F |
PTM55007 |
psi-fpm |
3,000 |
| k
(wear) factor |
PTM55010 |
|
100 |
| Thermal |
| Coefficient
of linear Thermal Expansion |
E-831(TMA) |
in/in/°F |
5.50x10ˆ-5 |
| Deflection
Temperature 264 psi |
D648 |
°F |
200 |
| Melting
Point (crystalline) peak |
D3418 |
°F |
420 |
| Continuous
Service Temperature in Air (Max.) |
|
°F |
260 |
| Thermal
Conductivity |
|
BTU-in/(hr-ft²°F) |
1.70 |
| Electrical |
| Dielectric
Strength, Short Term |
D149(2) |
Volts/mil |
500 |
| Surface
Resistivity |
EOS/ESD
S11.11 |
Ohm/square |
10ˆ13 |
| Dielectric
Constant, 10ˆ6 Hz |
D150(2) |
|
3.70 |
| Chemical |
| Acids,
Weak, 73°F/23°C, acetic acid, dilute hydrochloric or sulfuric |
Limited
Service |
| Acids,
Strong, 73°F/23°C, conc. hydrochloric or sulfuric |
Unacceptable |
| Alkalies,
Weak, 73°F/23°C, dilute ammonia or sodium hydroxide |
Limited
Service |
| Alkalies,
Strong, 73°F/23°C, conc. ammonia or sodium hydroxide |
Unacceptable |
| Hydrocarbons-Aromatic,
73°F/23°C, benzene, toluene |
Acceptable
Service |
| Hydrocarbons-Aliphatic,
73°F/23°C, gasoline, hexane, grease |
Acceptable
Service |
| Ketones,
Esters, 73°F/23°C, acetone, methyl ethyl ketone |
Acceptable
Service |
| Ethers,
73°F/23°C, diethyl ether, tetrahydrofuran |
Acceptable
Service |
| Chlorinated
Solvents, 73°F/23°C, methylene chloride, chloroform |
Limited
Service |
| Alcohols,
73°F/23°C, methanol, ethanol, anti-freeze |
Limited
Service |
| Inorganic
Salt Solutions, 73°F/23°C, sodium chloride, potassium cyanate |
Acceptable
Service |
| Continuous
Sunlight, 73°F/23°C |
Limited
Service |
| Miscellaneous |
| Water
Absorption Immersion, 24 hr |
D570 |
% |
0.30 |
| Water
Absorption Immersion, Sat. |
D570 |
% |
7.00 |
| Compliance |
| UL94 |
|
|
HB |
MC®
907 Natural
| Property |
Method |
Unit |
Value |
| Mechanical |
| Specific
Gravity, 73°F |
D792 |
|
1.15 |
| Tensile
Strength, 73°F |
D638 |
psi |
12,000 |
| Tensile
Modulus of Elasticity, 73°F |
D638 |
psi |
400,000 |
| Elongation,
73°F |
D638 |
% |
20.0 |
| Flexural
Strength, 73°F |
D790 |
psi |
16,000 |
| Flexural
Modulus, 73°F |
D790 |
psi |
500,000 |
| Shear
Strength, 73°F |
D732 |
psi |
11,000 |
| Compressive
Strength, 10% Def., 73°F |
D695 |
psi |
15,000 |
| Compressive
Modulus of Elasticity, 73°F |
D695 |
psi |
400,000 |
| Hardness,
Rockwell, Scale as noted, 73°F |
D785 |
|
M85
(R115) |
| Hardness,
Durometer, Shore D scale, 73°F |
D2240 |
|
D85 |
| Izod
Impact (notched), 73°F |
D256
Type A |
ft-lb/in |
0.4 |
| Coefficient
of Friction (Dry vs Steel) Dynamic |
PTM55007 |
|
0.20 |
| Limiting
PV, 73°F |
PTM55007 |
psi-fpm |
3,000 |
| k
(wear) factor |
PTM55010 |
|
100 |
| Thermal |
| Coefficient
of linear Thermal Expansion |
E-831(TMA) |
in/in/°F |
5.00x10ˆ-5 |
| Deflection
Temperature 264 psi |
D648 |
°F |
200 |
| Melting
Point (crystalline) peak |
D3418 |
°F |
420 |
| Continuous
Service Temperature in Air (Max.) |
|
°F |
200 |
| Thermal
Conductivity |
|
BTU-in/(hr-ft²°F) |
1.70 |
| Electrical |
| Dielectric
Strength, Short Term |
D149(2) |
Volts/mil |
500 |
| Surface
Resistivity |
EOS/ESD
S11.11 |
Ohm/square |
>10ˆ13 |
| Dielectric
Constant, 10ˆ6 Hz |
D150(2) |
|
3.70 |
| Chemical |
| Acids,
Weak, 73°F/23°C, acetic acid, dilute hydrochloric or sulfuric |
Limited
Service |
| Acids,
Strong, 73°F/23°C, conc. hydrochloric or sulfuric |
Unacceptable |
| Alkalies,
Weak, 73°F/23°C, dilute ammonia or sodium hydroxide |
Limited
Service |
| Alkalies,
Strong, 73°F/23°C, conc. ammonia or sodium hydroxide |
Unacceptable |
| Hydrocarbons-Aromatic,
73°F/23°C, benzene, toluene |
Acceptable
Service |
| Hydrocarbons-Aliphatic,
73°F/23°C, gasoline, hexane, grease |
Acceptable
Service |
| Ketones,
Esters, 73°F/23°C, acetone, methyl ethyl ketone |
Acceptable
Service |
| Ethers,
73°F/23°C, diethyl ether, tetrahydrofuran |
Acceptable
Service |
| Chlorinated
Solvents, 73°F/23°C, methylene chloride, chloroform |
Limited
Service |
| Alcohols,
73°F/23°C, methanol, ethanol, anti-freeze |
Limited
Service |
| Inorganic
Salt Solutions, 73°F/23°C, sodium chloride, potassium cyanate |
Acceptable
Service |
| Continuous
Sunlight, 73°F/23°C |
Limited
Service |
| Miscellaneous |
| Water
Absorption Immersion, 24 hr |
D570 |
% |
0.30 |
| Water
Absorption Immersion, Sat. |
D570 |
% |
7.00 |
| Compliance |
| UL94 |
|
|
HB |
| FDA |
|
|
Yes |
| USDA |
|
|
Yes |
| 3A-Dairy |
|
|
Yes |
Nylatron®
GS Nylon
| Property |
Method |
Unit |
Value |
| Mechanical |
| Specific
Gravity, 73°F |
D792 |
|
1.16 |
| Tensile
Strength, 73°F |
D638 |
psi |
12,500 |
| Tensile
Modulus of Elasticity, 73°F |
D638 |
psi |
480,000 |
| Elongation,
73°F |
D638 |
% |
25.0 |
| Flexural
Strength, 73°F |
D790 |
psi |
17,000 |
| Flexural
Modulus, 73°F |
D790 |
psi |
460,000 |
| Shear
Strength, 73°F |
D732 |
psi |
10,500 |
| Compressive
Strength, 10% Def., 73°F |
D695 |
psi |
16,000 |
| Compressive
Modulus of Elasticity, 73°F |
D695 |
psi |
420,000 |
| Hardness,
Rockwell, Scale as noted, 73°F |
D785 |
|
M85
(R115) |
| Hardness,
Durometer, Shore D scale, 73°F |
D2240 |
|
D85 |
| Izod
Impact (notched), 73°F |
D256
Type A |
ft-lb/in |
0.5 |
| Coefficient
of Friction (Dry vs Steel) Dynamic |
PTM55007 |
|
0.20 |
| Limiting
PV, 73°F |
PTM55007 |
psi-fpm |
3,000 |
| k
(wear) factor |
PTM55010 |
|
90 |
| Thermal |
| Coefficient
of linear Thermal Expansion |
E-831(TMA) |
in/in/°F |
6.40x10ˆ-5 |
| Deflection
Temperature 264 psi |
D648 |
°F |
200 |
| Melting
Point (crystalline) peak |
D3418 |
°F |
500 |
| Continuous
Service Temperature in Air (Max.) |
|
°F |
220 |
| Thermal
Conductivity |
|
BTU-in/(hr-ft²°F) |
1.70 |
| Electrical |
| Dielectric
Strength, Short Term |
D149(2) |
Volts/mil |
350 |
| Surface
Resistivity |
EOS/ESD
S11.11 |
Ohm/square |
10ˆ13 |
| Chemical |
| Acids,
Weak, 73°F/23°C, acetic acid, dilute hydrochloric or sulfuric |
Limited
Service |
| Acids,
Strong, 73°F/23°C, conc. hydrochloric or sulfuric |
Unacceptable |
| Alkalies,
Weak, 73°F/23°C, dilute ammonia or sodium hydroxide |
Limited
Service |
| Alkalies,
Strong, 73°F/23°C, conc. ammonia or sodium hydroxide |
Unacceptable |
| Hydrocarbons-Aromatic,
73°F/23°C, benzene, toluene |
Acceptable
Service |
| Hydrocarbons-Aliphatic,
73°F/23°C, gasoline, hexane, grease |
Acceptable
Service |
| Ketones,
Esters, 73°F/23°C, acetone, methyl ethyl ketone |
Acceptable
Service |
| Ethers,
73°F/23°C, diethyl ether, tetrahydrofuran |
Acceptable
Service |
| Chlorinated
Solvents, 73°F/23°C, methylene chloride, chloroform |
Limited
Service |
| Alcohols,
73°F/23°C, methanol, ethanol, anti-freeze |
Limited
Service |
| Inorganic
Salt Solutions, 73°F/23°C, sodium chloride, potassium cyanate |
Acceptable
Service |
| Continuous
Sunlight, 73°F/23°C |
Limited
Service |
| Miscellaneous |
| Water
Absorption Immersion, 24 hr |
D570 |
% |
0.30 |
| Water
Absorption Immersion, Sat. |
D570 |
% |
7.00 |
| Compliance |
| UL94 |
|
|
V-2 |
Nylatron®
GSM Blue Nylon
| Property |
Method |
Unit |
Value |
| Mechanical |
| Specific
Gravity, 73°F |
D792 |
|
1.15 |
| Tensile
Strength, 73°F |
D638 |
psi |
10,000 |
| Tensile
Modulus of Elasticity, 73°F |
D638 |
psi |
500,000 |
| Elongation,
73°F |
D638 |
% |
30.0 |
| Flexural
Strength, 73°F |
D790 |
psi |
15,000 |
| Flexural
Modulus, 73°F |
D790 |
psi |
500,000 |
| Compressive
Strength, 10% Def., 73°F |
D695 |
psi |
13,000 |
| Compressive
Modulus of Elasticity, 73°F |
D695 |
psi |
425,000 |
| Hardness,
Rockwell, Scale as noted, 73°F |
D785 |
|
M80
(R117) |
| Izod
Impact (notched), 73°F |
D256
Type A |
ft-lb/in |
0.9 |
| Coefficient
of Friction (Dry vs Steel) Dynamic |
PTM55007 |
|
0.18 |
| Limiting
PV, 73°F |
PTM55007 |
psi-fpm |
5,500 |
| k
(wear) factor |
PTM55010 |
|
65 |
| Thermal |
| Coefficient
of linear Thermal Expansion |
E-831(TMA) |
in/in/°F |
5.50x10ˆ-5 |
| Deflection
Temperature 264 psi |
D648 |
°F |
200 |
| Melting
Point (crystalline) peak |
D3418 |
°F |
420 |
| Continuous
Service Temperature in Air (Max.) |
|
°F |
200 |
| Electrical |
| Surface
Resistivity |
EOS/ESD
S11.11 |
Ohm/square |
10ˆ13 |
| Chemical |
| Acids,
Weak, 73°F/23°C, acetic acid, dilute hydrochloric or sulfuric |
Limited
Service |
| Acids,
Strong, 73°F/23°C, conc. hydrochloric or sulfuric |
Unacceptable |
| Alkalies,
Weak, 73°F/23°C, dilute ammonia or sodium hydroxide |
Limited
Service |
| Alkalies,
Strong, 73°F/23°C, conc. ammonia or sodium hydroxide |
Unacceptable |
| Hydrocarbons-Aromatic,
73°F/23°C, benzene, toluene |
Acceptable
Service |
| Hydrocarbons-Aliphatic,
73°F/23°C, gasoline, hexane, grease |
Acceptable
Service |
| Ketones,
Esters, 73°F/23°C, acetone, methyl ethyl ketone |
Acceptable
Service |
| Ethers,
73°F/23°C, diethyl ether, tetrahydrofuran |
Acceptable
Service |
| Chlorinated
Solvents, 73°F/23°C, methylene chloride, chloroform |
Limited
Service |
| Alcohols,
73°F/23°C, methanol, ethanol, anti-freeze |
Limited
Service |
| Inorganic
Salt Solutions, 73°F/23°C, sodium chloride, potassium cyanate |
Acceptable
Service |
| Continuous
Sunlight, 73°F/23°C |
Limited
Service |
| Miscellaneous |
| Water
Absorption Immersion, 24 hr |
D570 |
% |
0.22 |
| Water
Absorption Immersion, Sat. |
D570 |
% |
6.00 |
| Compliance |
| UL94 |
|
|
HB |
| 3A-Dairy |
|
|
Yes |
Nylatron®
GSM Nylon
| Property |
Method |
Unit |
Value |
| Mechanical |
| Specific
Gravity, 73°F |
D792 |
|
1.16 |
| Tensile
Strength, 73°F |
D638 |
psi |
11,000 |
| Tensile
Modulus of Elasticity, 73°F |
D638 |
psi |
400,000 |
| Elongation,
73°F |
D638 |
% |
30.0 |
| Flexural
Strength, 73°F |
D790 |
psi |
16,000 |
| Flexural
Modulus, 73°F |
D790 |
psi |
500,000 |
| Shear
Strength, 73°F |
D732 |
psi |
10,500 |
| Compressive
Strength, 10% Def., 73°F |
D695 |
psi |
14,000 |
| Compressive
Modulus of Elasticity, 73°F |
D695 |
psi |
400,000 |
| Hardness,
Rockwell, Scale as noted, 73°F |
D785 |
|
M80
(R110) |
| Hardness,
Durometer, Shore D scale, 73°F |
D2240 |
|
D85 |
| Izod
Impact (notched), 73°F |
D256
Type A |
ft-lb/in |
0.5 |
| Coefficient
of Friction (Dry vs Steel) Dynamic |
PTM55007 |
|
0.20 |
| Limiting
PV, 73°F |
PTM55007 |
psi-fpm |
3,000 |
| k
(wear) factor |
PTM55010 |
|
90 |
| Thermal |
| Coefficient
of linear Thermal Expansion |
E-831(TMA) |
in/in/°F |
6.00x10ˆ-5 |
| Deflection
Temperature 264 psi |
D648 |
°F |
200 |
| Melting
Point (crystalline) peak |
D3418 |
°F |
420 |
| Continuous
Service Temperature in Air (Max.) |
|
°F |
200 |
| Electrical |
| Dielectric
Strength, Short Term |
D149(2) |
Volts/mil |
400 |
| Surface
Resistivity |
EOS/ESD
S11.11 |
Ohm/square |
10ˆ13 |
| Dielectric
Constant, 10ˆ6
Hz |
D150(2) |
|
3.70 |
| Chemical |
| Acids,
Weak, 73°F/23°C, acetic acid, dilute hydrochloric or sulfuric |
Limited
Service |
| Acids,
Strong, 73°F/23°C, conc. hydrochloric or sulfuric |
Unacceptable |
| Alkalies,
Weak, 73°F/23°C, dilute ammonia or sodium hydroxide |
Limited
Service |
| Alkalies,
Strong, 73°F/23°C, conc. ammonia or sodium hydroxide |
Unacceptable |
| Hydrocarbons-Aromatic,
73°F/23°C, benzene, toluene |
Acceptable
Service |
| Hydrocarbons-Aliphatic,
73°F/23°C, gasoline, hexane, grease |
Acceptable
Service |
| Ketones,
Esters, 73°F/23°C, acetone, methyl ethyl ketone |
Acceptable
Service |
| Ethers,
73°F/23°C, diethyl ether, tetrahydrofuran |
Acceptable
Service |
| Chlorinated
Solvents, 73°F/23°C, methylene chloride, chloroform |
Limited
Service |
| Alcohols,
73°F/23°C, methanol, ethanol, anti-freeze |
Limited
Service |
| Inorganic
Salt Solutions, 73°F/23°C, sodium chloride, potassium cyanate |
Acceptable
Service |
| Continuous
Sunlight, 73°F/23°C |
Limited
Service |
| Miscellaneous |
| Water
Absorption Immersion, 24 hr |
D570 |
% |
0.30 |
| Water
Absorption Immersion, Sat. |
D570 |
% |
7.00 |
| Outgassing
TML (Total Mass Loss) |
E595 |
% |
2.00 |
| CVCM
(Collected Volatile Condensable Material) |
E595 |
% |
0.00 |
| WVR
(Water Vapor Regained) |
E595 |
% |
0.70 |
| Compliance |
| UL94 |
|
|
HB |
Nylatron®
NSM Nylon
| Property |
Method |
Unit |
Value |
| Mechanical |
| Specific
Gravity, 73°F |
D792 |
|
1.15 |
| Tensile
Strength, 73°F |
D638 |
psi |
11,000 |
| Tensile
Modulus of Elasticity, 73°F |
D638 |
psi |
410,000 |
| Elongation,
73°F |
D638 |
% |
20.0 |
| Flexural
Strength, 73°F |
D790 |
psi |
16,000 |
| Flexural
Modulus, 73°F |
D790 |
psi |
475,000 |
| Shear
Strength, 73°F |
D732 |
psi |
10,000 |
| Compressive
Strength, 10% Def., 73°F |
D695 |
psi |
14,000 |
| Compressive
Modulus of Elasticity, 73°F |
D695 |
psi |
400,000 |
| Hardness,
Rockwell, Scale as noted, 73°F |
D785 |
|
M80
(R110) |
| Hardness,
Durometer, Shore D scale, 73°F |
D2240 |
|
D85 |
| Izod
Impact (notched), 73°F |
D256
Type A |
ft-lb/in |
0.5 |
| Coefficient
of Friction (Dry vs Steel) Dynamic |
PTM55007 |
|
0.18 |
| Limiting
PV, 73°F |
PTM55007 |
psi-fpm |
15,000 |
| k
(wear) factor |
PTM55010 |
|
9 |
| Thermal |
| Coefficient
of linear Thermal Expansion |
E-831(TMA) |
in/in/°F |
5.20x10ˆ-5 |
| Deflection
Temperature 264 psi |
D648 |
°F |
200 |
| Melting
Point (crystalline) peak |
D3418 |
°F |
420 |
| Continuous
Service Temperature in Air (Max.) |
|
°F |
200 |
| Electrical |
| Dielectric
Strength, Short Term |
D149(2) |
Volts/mil |
400 |
| Surface
Resistivity |
EOS/ESD
S11.11 |
Ohm/square |
10ˆ13 |
| Chemical |
| Acids,
Weak, 73°F/23°C, acetic acid, dilute hydrochloric or sulfuric |
Limited
Service |
| Acids,
Strong, 73°F/23°C, conc. hydrochloric or sulfuric |
Unacceptable |
| Alkalies,
Weak, 73°F/23°C, dilute ammonia or sodium hydroxide |
Limited
Service |
| Alkalies,
Strong, 73°F/23°C, conc. ammonia or sodium hydroxide |
Unacceptable |
| Hydrocarbons-Aromatic,
73°F/23°C, benzene, toluene |
Acceptable
Service |
| Hydrocarbons-Aliphatic,
73°F/23°C, gasoline, hexane, grease |
Acceptable
Service |
| Ketones,
Esters, 73°F/23°C, acetone, methyl ethyl ketone |
Acceptable
Service |
| Ethers,
73°F/23°C, diethyl ether, tetrahydrofuran |
Acceptable
Service |
| Chlorinated
Solvents, 73°F/23°C, methylene chloride, chloroform |
Limited
Service |
| Alcohols,
73°F/23°C, methanol, ethanol, anti-freeze |
Limited
Service |
| Inorganic
Salt Solutions, 73°F/23°C, sodium chloride, potassium cyanate |
Acceptable
Service |
| Continuous
Sunlight, 73°F/23°C |
Limited
Service |
| Miscellaneous |
| Water
Absorption Immersion, 24 hr |
D570 |
% |
0.25 |
| Water
Absorption Immersion, Sat. |
D570 |
% |
7.00 |
| Compliance |
| UL94 |
|
| |